Instruction Manual

Opening the vault with the Backup Key

1. Locate the handle spokes included in the shipping carton. Mount the three spokes to the handle hub.
2. A key slot is located behind the lock cover. To remove the cover, press the tab to the left and turn the lock cover counterclockwise.
3. Insert one of your back up keys into the keyhole and turn it counterclockwise. At the same time, turn the door handle clockwise to open the door.

Battery Installation

1. With the lock cover removed, locate the battery compartment.
2. Connect a 9V alkaline battery (not included) to the battery connecting cap matching the polarity (+/-) as indicated.
3. When the battery is connected correctly, the indicator light will light up once with 1 beep.
4. Replace the lock cover and turn it clockwise, back into its original position.

IMPORTANT: When changing the battery, always hold the battery connecting cap while disconnecting or attaching the battery. Do not pull on the wires.

Master Code Programming

First time users should change the default code as soon as possible to prevent unauthorized access to your vault. The code should be kept confidential.

Tips: Code Requirements

• Programming a new code will overwrite your previous code.
• Your code can be a minimum of 4 and a maximum of 6 digits.
• Two keys cannot be pressed simultaneously.
• Press any number key (1, 2, 3, or 4) to wake up the system before entering your passcode.

1. To get started, wake up the system and enter default code 1-2-3-4 on the keypad to open your vault.
2. With the vault open, press the Program Button (located on the inside of the vault door) once and release it.  The indicator light will light up BLUE once with 1 beep.
3. Enter your NEW master code.
4. Press the Program Button once and release it.  The indicator light will light up BLUE 2 times with 2 beeps.
5. Now test the passcode after waking up the system. If you set the passcode unsuccessfully, the indicator light will light up RED 5 times with 5 beeps, and the new code will not work.  You must repeat the above steps to reset the code.

Fingerprint Registration

1. With the vault open, press the Program Button once and release it.  The indicator light will light up BLUE once with 1 beep.
2. Place your finger on the fingerprint sensor for the 1st of 4 scans. Remove your finger after the indicator light lights up BLUE once with 1 beep. Place the same finger again over the fingerprint sensor until the indicator light lights up Blue once with 1 beep. You will repeat this process until the indicator light lights up BLUE 2 times with 2 beeps.
3. Now your fingerprint has been successfully registered.
4. Test your fingerprint. If you registered the fingerprint unsuccessfully, the new fingerprint will not work. You must repeat the above steps to re-register your fingerprints.

NOTE: You cannot register more than 20 fingerprints. If the indicator light lights up RED 5 times with 10 beeps when you register your fingerprint, it means the fingerprint storage capacity is full.

Helpful Programming Tips:

1. Place your finger on the center of the sensor. This allows the sensor to read where most of the fingerprint detail is located.
2. Adjust your finger slightly between scans for increased accuracy.
3. Excessive moisture, lotion, or dirt will affect your fingerprint and may cause inaccurate sensor reading.
4. If you are experiencing difficulty, try different fingers. Each finger is unique, and some fingers such as your thumb, contain more readable information than others.
5. To increase your success rate, please register the same fingerprint multiple times.

Registered Fingerprint Deleting

1. Press and hold the Program Button until the indicator light lights up BLUE 2 times with 2 beeps.
2. Now all previously registered fingerprints are erased.

Lock-Down System

• If you enter the wrong code or unregistered fingerprints, the indicator light will light up RED 5 times with 5 beeps.
• If the wrong code or an unregistered fingerprint is entered 5 consecutive times, the vault will go into a lock-down mode for 5 minutes.
• While in lock-down mode, the indicator light will keep flashing RED and the keypad and fingerprint sensor will be temporarily disabled.
• The vault can still be opened by using the back up keys override.
• After 5 minutes, the vault will automatically resume normal operation.

Low Battery Warning

If the indicator light lights up BLUE 1 second, and then lights up RED 10 times with 10 beeps when opening the vault without a key, this indicates that your battery level is critically low and the battery needs to be replaced.

Vibration Alarm Setting

Press and hold the number “4” for 4 seconds until you hear 1 beep and the indicator light lights up together.

NOTE: When the alarm is triggered, the keypad and fingerprint sensor will be temporarily disabled. The vault can still be opened by using the back up keys.  After the alarm is deactivated, you need to reset the above steps.

Locking the vault

Turn the door handle counterclockwise to close the door.

Silence Mode Setting

To silence the audible sound of the touchscreen, hold the number “ 1” for 3 seconds, until the indicator light lights up. To unmute the keys, repeat this step, you will hear 1 beep and the indicator light lights up together.